Tank Mechanic Simulator for Mac Detailed Operation Guide

II. Complete Workflow from Creating a Project to Exporting

This workflow uses completing a full tank repair order as an example.

2.1 Create/Open a Project: Accept a Repair Order

The game progresses in units of “projects” (i.e., repair orders).

1. Launch the game and select “Continue” from the main menu to load an existing save, or “New Game” to create a new save.
2. After entering the garage, press the Tab key to open the warehouse interface.
3. Switch to the “Tasks” tab. Here you will see a list of available tank repair orders.
4. Browse the orders to check the tank model, repair requirements (e.g., “Repair to operational condition”), and payment. Click the “Accept” button in the lower right corner of the order.
5. Once accepted, the tank will appear in your “Tank Library.” This is your new “project.”

2.2 Core Repair Workflow: Inspect, Disassemble, Repair, Reassemble

Step 1: Initial Inspection and Identification

1. In the Tank Library, click on the tank from the order you just accepted and select “Move to Garage.”
2. Facing the tank, hold the flashlight (select it from the tool panel or press the number key 1) and shine it on the tank’s surface.
3. Move the cursor over various parts of the tank (hull, turret, tracks, etc.). When a gear icon appears, it indicates an interactable part. Right-click to perform an “Inspect” to identify the part. Press J to open the handbook for reference.

Step 2: Disassemble the Tank

1. Following the manual or order requirements, disassemble from the outside in. For example, first remove the external tracks and side panels, then proceed to the internal engine and transmission.
2. Aim the cursor at the identified component and hold the left mouse button (or press the specified key as prompted) to begin disassembly. Complex components may require removing multiple screws first (using a screwdriver tool).
3. Removed components will fall to the ground. Aim at the component on the ground and press E to pick it up. Small components (such as screws and pistons) will automatically go into your backpack; large components (such as engine blocks) require using the crane in the garage (press F to aim at the component and operate) to hoist them to the workbench or parts rack.
4. Press Tab to open the inventory, and drag components from your backpack and the ground to the parts rack for categorized storage and easier management.

Step 3: Clean and Repair Components

1. Go to the parts rack, select a component that needs processing (such as a rusty transmission), and click “Move to Workbench.”
2. On the workbench interface, use the following tools in order:
   • Brush/Scraper (number keys 2/3): Remove large chunks of dirt and rust.
   • Sandblaster (number key 4): Thoroughly remove all rust traces and reveal the bare metal. This is a necessary step for repairing most components.
   • Welding Machine (Hotkey 5): If a component has a “damaged” status (shown as red cracks), you need to aim at the cracks and hold the left mouse button to weld them.
3. Once repairs are complete, the component status will change from “rusty/damaged” to “repaired.” Place it back on the parts rack.

Step 4: Reassemble the Tank

1. Ensure all required components have been repaired and are placed on the parts rack or in your backpack.
2. In the garage, open the manual (J) for reference.
3. Begin assembly starting from the core components (e.g., first reinstall the repaired engine onto the hull). Aim at the installation points inside the hull, and when a green wheel appears, press E to place it.
4. When installing screws and other fasteners, you need to select the corresponding screw type from your backpack, aim at the threaded hole and press E to place it, then use the Wrench (Hotkey 6) to tighten it.
5. Repeat this process in order from inside to outside until all components are installed.

2.3 Final Testing and “Export” (Delivering the Order)

1. Once assembly is complete, enter the tank cockpit (press E near the cockpit).
2. Try starting the engine (there is usually an interactive prompt). If all key components are installed correctly and have been repaired, the engine should start successfully.
3. Press Tab to open the inventory, then go to the “Tank Library”.
4. Find the repaired tank; its status should be displayed as “Repaired” or “Operational”.
5. Click the “Complete Order” button below the tank information. The system will perform a final check; once it confirms that the order requirements are met, it will pay out the reward, and the project (order) will be marked as complete——the “export” process is finished.

III. Advanced Tips for Common Features

• Efficient disassembly: When disassembling large composite parts (such as the engine), first check “Show all subcomponents” on its information panel, then use the “Disassemble All” feature to quickly remove all related small parts and save time.
• Assistant management: Once you have earned enough money, hire assistants in the “Assistants” tab of the “Inventory” interface. Assign them to “Exploration” missions so they can automatically bring back tanks and parts for you—an important source of resources. Upgrade their skills regularly.
• Painting tips: Before painting (number key 7), make sure the vehicle body surface is completely clean and rust-free; otherwise, the paint will not adhere. While painting, keep moving the mouse evenly to avoid piling up paint in one spot.
• Quick Tool Switching: In addition to clicking tools on the panel with the mouse, proficiently using the number keys 1-8 to quickly switch tools is key to improving operational fluency.
• Using Filters and Sorting: When there are many parts and items, use the filter buttons above (by type, status) and the sorting function to quickly locate the parts you need.

IV. Common Problems and Solutions

• Problem: Parts cannot be installed, and the green wrench does not appear.
  
  Solution: ① Check the manual to confirm whether the installation sequence is correct. ② Confirm whether the part has been repaired (status is green). ③ Check whether there are other uninstalled parent parts blocking it. ④ Try slightly moving the viewing angle to find the exact installation point.
• Problem: The sandblaster cannot remove all rust marks.
  
  Solution: Make sure you are using the sandblaster (4) rather than the brush (2). Aim at the rust mark area and move slowly to ensure all surfaces are covered. Some dark stains are the base color of the paint and do not need to be cleaned.
• Problem: The game stutters or the frame rate is low.
  
  Solution: In the game settings (Esc > Settings), appropriately lower the graphics quality, especially “Shadow Quality,” “Post-processing,” and “View Distance.” Make sure the Mac has good heat dissipation.
• Problem: Cannot find a specific part.
  
  Solution: ① Confirm the exact name of the part in the Handbook (J). ② Use the filter function in the Parts Rack and sort by name. ③ The part may not yet have been discovered in Exploration or may never have been dismantled before, and needs to be purchased or obtained through Exploration.
• Problem: The crane (F) cannot pick up parts.
  
  Solution: Make sure the crane hook has been lowered (there is usually an up/down control prompt), and that you are aiming at the center or main structural part of the component rather than an edge or corner.

V. Keyboard Shortcuts Summary (Mac Version)